Home >

tomato

Advertisement
  • Port forwarding to VPN clientOctober 15

    I have a router on Tomato (shibby) running an OpenVPN server (with TAP; interface is tap21 on the router). Various resources (including some workstations) are physically connected to eth0 on this router. I have another physical device across the coun

  • Forwarding ports to server in VPNJune 19

    I have a router on Tomato (shibby) running an OpenVPN server (with TAP; interface is tap21 on the router). Various resources (including some workstations) are physically connected to eth0 on this router. I have another physical device across the coun

  • Windows + Tomato - Client 2 Client logic = help pleaseJanuary 28

    I tried searching, I promise.. I always try figuring it out with the help of Searches, but I'm stuck. 3+ days into it, and I've got my logic all twisted around :( Background: Client wants a (seemingly simple) VPN solution to connect his main-office(s

  • Router not listing devices connected through POE switchJanuary 27

    I have an ASUS RT AC66U and a TP-Link Archer C9 (AC1900) router. I have 4 cameras with static IP addresses connected through a POE switch. If I connect the POE switch to my TP-Link with its default firmware, it shows all devices connected through the

  • How do I create another LAN interface on my AP?January 23

    My home network set up is: WAN > Pfsense router > Wireless AP with tomato firmware on it. On my AP, I have 2 wifi networks. Home and Guest. What I want to do is create two VLANs on my AP. I want to bridge one VLAN to my home wifi and bridge the othe

  • DD-WRT/Tomato Routing traffic out interface based on source IP/Port January 22

    I've been trying to figure this out on my own for a while now and have gotten nowhere. I want to set up a Dual WAN configuration but don't want a failover, or load balancing setup. I've read a few tutorials for these setups but they seem more complic

  • Iptables route specific port outside VPN (Tomato router firmware)January 9

    Im trying to configure my router to what I feel is the perfect setup for me. I have managed to connect the router to my VPN-provider (PIA), and routed such that only one computer connects through VPN via iptables (see answere #4 http://serverfault.co

  • HTTPS access to Tomato admin pageJanuary 9

    Today in Tomato administration interface I switched access method to the interface from HTTP to HTTPS. The router (OVISLINK AirLive WL-1600GL) restarted itself and currently an attempt to connect results in: An error occurred during a connection to 1

  • Secured link to connect & access across 2 separate LAN Subnets using CAT 6?

    Secured link to connect & access across 2 separate LAN Subnets using CAT 6?January 8

    Secured link to connect & access across 2 separate LAN Subnets using CAT 6? Following is an older diagram of a 2+1 level Small Business/ Startup + Co-working space, with recent expansion & need for integration. The following changes & informat

  • Can Freeradius version 3 be package into Optware?December 12

    I have optware running on a WNR 3500 v1 wifi router running Tomato / USB. But freeradius is version 2.X and has an issue. Where may I find v3 or how to I go about making a package?

  • Can't access tomato router websiteDecember 8

    Most probably I've locked myself out of my tomato router and I'm wondring if it's permanent or there could be any way around. The only open ports are: 53 443 The router has IP address, and creates WIFI network (with strong password). The most severe

  • Connect a WiFi Repeater with a Tomato RouterDecember 6

    I recently bought a repeater (http://en.avm.de/products/fritzwlan/fritzwlan-repeater-1750e/) to extend the range of my wifi, but I'm not able to make it work with my router (ASUS RT-68AC) which runs Advanced Tomato (Tomato Firmware 1.28.0000 MIPSR2-3

  • Configure tomato firewall in VM or Debian / CentOs serverNovember 24

    I want to use tomato as my internal firewall for accept/block network packets inside my server system. I know that tomato provides firmware for some routers but I want to do some tricky but don't know I am on right way or not. I have downloaded sourc

  • Asus RT-N16 + LinkSys E1000v1 network bridge (AP+WDS) for Guest Network

    Asus RT-N16 + LinkSys E1000v1 network bridge (AP+WDS) for Guest NetworkNovember 16

    I am trying to extend my Guest Network on my wifi router Asus RT-N16 by adding LinkSys E1000v1 in the far area of the house. However, I cannot make LinkSys work and I am not sure how to trobleshoot it. I tried to mimic Asus FAQ guide and alternative

  • How to limit access on an access point?

    How to limit access on an access point?November 7

    I have a Linksys router running Tomato Shibby. Connected to that main router is a wireless access point. I would like devices connected to the wireless AP to be limited by bandwidth. Can someone teach me how please? Thank you --------------Solutions-

  • Routing OpenVPN traffic through a TomatoUSB routerOctober 27

    I have setup a Tomato USB, on my second (internal) router. The outside router simply forwards VPN traffic to it, and it acts as a VPN server. I can connect to the VPN server and my local area networks, but I lose internet connectivity. I know why: I

  • Is it possible to route all traffic to a vpn except multicasts?October 26

    I am using a router with tomato firmware installed. My lan includes a tv, eg ip 192.168.0.2. The tv receives multicast broadcasts from an iptv provider, but can also access the internet to view youtube etc. It looks like the multicast broadcast is co

  • Allow access to camera only by one IP - tomatoOctober 26

    I'm running tomato shibby 1.2.8 on an ASUS router. I have a camera in my network, which has the IP 192.168.1.222 (static IP). I would like to block all connections to this IP, where the source is anything but 192.168.1.1 (router itself). Why I want t

  • tomatousb - Allow only specific IP to connect to other IP portOctober 16

    I'm using tomato shibby on a router, and I'm trying to set some specific rules using iptables to set the following: I have a server, which runs on 192.168.1.2 (LAN) port 2232. Everybody from the LAN can access it. I want to make sure the server is ac

  • Tomato router killswitch using iptablesOctober 1

    I have a tomato router setup with a VPN service. Everything works fine and I also have it that when the VPN drops it kills the connection so that any device connected to that router would never go through the local Internet. I have found a problem wh

Copyright (C) 2018 ceus-now.com, All Rights Reserved. webmaster#ceus-now.com 14 q. 0.564 s.