Home > rs232 > Use of RS-232 interfacing

Use of RS-232 interfacing

May 16Hits:1
Advertisement

The RS-232 serial adapter is used very frequently with micro controller. I am new to electronics and I am eager to know why it is used between bluetooth module and micro controller.

Tags:rs232

Related Articles

  • Use of RS-232 interfacingMay 16

    The RS-232 serial adapter is used very frequently with micro controller. I am new to electronics and I am eager to know why it is used between bluetooth module and micro controller.

  • Interfacing barcode scanner with microcontrollerMarch 22

    I am doing a project involving barcode scanner, netduino plus 2(microcontroller). I came across different types of interfaces(pin standard used such as USB etc..) for barcode scanners which are Keyboard wedge, RS232, USB (which again acts as keyboard

  • Do you really need all of the sigals for a general RS-232 port?April 12

    I know that having TX, RX, GND, RTS, CTS are good. What about all of the others? Do devices these days even make use of the other pins (DSR, RI, DCD, DTR)? Is it safe to generally leave out these pins? It seems to me like these are mostly only used i

  • How can RS-232 DTR / RTS pins be used for power?October 28

    I want to interface to this device where (sec 4.2) states can be powered from the DTR and RTS handshaking lines by having one high and one low Also, Wikipedia states: No method is specified for sending power to a device. While a small amount of curre

  • Setting RS-232 RTS pinJanuary 14

    I am experimenting with my PC's RS-232 interface on Win7. I want to toggle the RTS line state with "mode com1: rts=on" command. However monitoring the RTS line with multimeter shows that the state of the line is momentarily pulsed to on-state. I

  • USB-232 converters - rts/cts latency problemSeptember 10

    I am integrating the USB controller FT230X into a new product. It interfaces directly with the 32 bit Cortex M4 MCU, the STM32F303x The receive buffer on the STM32 is only 2 bytes deep, which I assumed would not be a problem since I could use the RTS

  • What infomation can be had about a USB device that I don't have drivers for?July 2

    I have a USB device (USB to RS-232) that works on some computers without drivers but not on others. This is a problem because I don't have the drivers disk for it nor any info on who made it. Are there any tools that will tell me what kind of device

  • Programming a parallel port as digital I/OJuly 12

    I'm trying to use a parallel port from a computer as a form of cheap digital output to do various things (control motors, light LEDs, read limit switches, ect). I want to know how to control the 8 data pins on a parallel port using C++, however there

  • What protocol does a TDD/TTY use to communicate with a cell phone's headset jack?September 24

    Some cell phones are TTY/TDD (telecommunications device for the deaf) compatible, meaning a terminal can be plugged into the headset jack for text communications. Is it just a hidden RS-232 interface? --------------Solutions------------- TTY/TDD uses

  • Common digital "glue" chips used with Arduino/Netduino?May 19

    I have a Netduino Plus and I am trying to put together a shopping list to one of my usual vendors for digital "glue" parts I can use with it. I am experienced in electronics but I haven't bought IC's (other than regulators) in a while. This is a

  • Why would you connect a 15-pin VGA connector to a 9-pin DB connector? August 17

    Anyone have any idea what one would connect with this cable? Going from a 15-pin VGA connector to a DB9 is very odd. 1.5M VGA HD15 Male to DB9 Pin Male Adapter Cable White The reason I ask is that in an effort to get some hardware that required a ser

  • RS232 which pin i can connect together to receive a input signal in my Java application listening on ttyUSB0 or ttyS0?September 15

    I am trying to make a very simple BUTTON (simple wire RED/YELLOW only). Now if the Button is pressed (RED touch YELLOW) i want to receive input signal in my Java application (that button was pressed). In which ports of RS233(DB9) i should patch the R

  • GPS detected as serial mouseSeptember 30

    I'm not sure if this question is in the right stackexchange site because it's a mix of programming and hardware. Admin, feel free to move it to another stackexchange site. Here is the problem: I've programmed a small application (C++ MFC) that read t

  • Generic PIC 40-Pin and 18-pin development boardsOctober 1

    I've looked at Guide in choosing good overall PIC dev board page already, but didn't really find what I'm looking for. I have found some 18-pin, 28-pin, and 40-pin PIC development boards at Sparkfun http://www.sparkfun.com/categories/9 . However, I w

  • Optotriac doesn't turn off

    Optotriac doesn't turn offOctober 28

    I'm using an opto triac, specifically the MOC3041, with a zero crossing circuit to switch the Tx pinout on an RS-232 interface. I have no problems turning it on, but after I unload the input (no input current), the triac doesn't turn off. The load is

  • Serial data transfer from Omega DP80 legacy hardware to computer

    Serial data transfer from Omega DP80 legacy hardware to computerJanuary 11

    Can anyone provide me with some guidance on setting up a legacy serial connection on an Omega (brand) thermocouple display? I would like to use the serial data interface (Omega DP80-Ser) to reliably transfer an ASCII text string over RS-232 serial co

  • I2C - RS232 controller

    I2C - RS232 controllerApril 17

    anyone have reccomendations for an IC that can be used to access a device with an RS-232 interface from an I2C bus? Id rather have something that doesnt need programming as I already have a uC master onthe bus that is taking up a good percentage of m

  • Cipher Feedback Mode

    Cipher Feedback ModeApril 27

    I can't understand what CFB really is. It said in Wikipedia that CFB is same as CBC, but I find that CFB is more difficult than CBC. Can someone explain to me how CFB works. Such as how Initialization Vector(IV) work inside the Encryption Algorithm p

  • AVR in system programming (ISP)

    AVR in system programming (ISP)May 19

    Can I use this programmer to program an onboard Atmega168 TQFP chip? Does the board have to be powered up or the programmer supplies it's own +5v? Here's what the programmer's schematic looks like. --------------Solutions------------- You'll have to

  • Setup null modem connection with a phone like cable

    Setup null modem connection with a phone like cableJuly 4

    I have a device that i want to connect with, reading the user's manual it claims that i can connect to the device via SR-232 interface and it list all the steps to configure a null modem connection on widows 7 an use that connection with its own soft

Copyright (C) 2018 ceus-now.com, All Rights Reserved. webmaster#ceus-now.com 14 q. 0.503 s.